Needing Dexter Hub # 8-91A
Question:
Hello, I am looking to purchase a 125 Dexter Hub # 8-91a. I cant seem to find this Hub on your website. Thanks,
asked by: Kodey
0
Expert Reply:
The hub that you are looking for comes in the Trailer Hub Assembly # 8-91-05UC1 on our site. For the E-Z Lube version you would instead want the Trailer Hub Assembly # 8-91-05UC1-EZ.
I contacted Dexter Axle and confirmed that these were the correct hubs for the 8-91A hub you are looking to purchase.
expert reply by:
Jon G
0
Products Referenced in This Question
Dexter Trailer Idler Hub Assembly for 2,000-lb E-Z Lube Axles - 4 on 4 - L44649 Bearings
- Trailer Hubs and Drums
- Hub
- EZ Lube
- L44649
- L44649
- For 2000 lbs Axles
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- Dexter
more information >
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings
- Trailer Hubs and Drums
- Hub
- Standard
- L44649
- L44649
- For 2000 lbs Axles
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- Dexter
more information >
Continue Researching
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Search Results: 8 91a hub
- Shop: Square 2-Speed Jack - Drop Leg w/ Spring Return - Weld On - Sidewind - 25K
- Search Results: tjd2sp~25100
- Shop: Lippert Manual Pull-Out Step for RVs - Single - 6" Drop - 24-1/4" Wide - Steel - 300 lbs
- Search Results: rv folding steps
- Search Results: dexter hub 8 248
- Search Results: dexter 8 213
- Shop: Trailer Wiring
- Video: Performance Tool Hitch Aligners - Rods and Lights - PTW1276 Review
- Search Results: 84545uc1~ez
- Search Results: 7 way connector
- Shop: Dexter Trailer Idler Hub Assembly for 5,200-lb to 7,000-lb E-Z Lube Axles - 8 on 6-1/2
- Shop: Dexter Trailer Idler Hub Assembly for 5,200-lb E-Z Lube Axles - 6 on 5-1/2
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-3/4 - Pre-Greased
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 6 on 5-1/2 - Pre-Greased
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Q&A: Replacement Bearings and Seals for a Dexter Hub with 8-91A Stamped on Back
- Q&A: Replacement Trailer Wheel Center Cap Plug for Aluma Trailer Wheels
- Q&A: How to Grease a Dexter EZ Lube Axle
- Q&A: What is the Best Grease for Trailer Bearings
- Q&A: Is There a Risk of Adding Too Much Grease to an EZ-Lube Spindle
- Video: TryRyde Tang Type Replacement Spindle Washer Review
- Video: Review of Dexter Trailer Hubs and Drums - Hub - 34822545BX
- Video: TruRyde E-Z Lube Grease Caps Plug Review
- Video: Dexter Replacement EZ Lube Drive-In Grease Cap Review
- Article: Overview of Lubricating Grease
- Q&A: Replacement Dexter Hub for 8-91A Hub
- Q&A: Replacement Trailer Wheel for Trailer with 1.062-Inch Diameter Spindle
Bob D.
6/3/2020
Similar question.I am considering replacing bearings, seals, races and possible hubs on 1986 my Starcraft popup camper. Dexter Hub # is also 8-91A. Straight spindle with 1.500" and 1.062" diameters. Both bearings are L44549 which I believe to have been replaced By L44649? the seal is National 474276. Do you have a kit for replacing bearings, seals, and races? If I decided to replace hub assemblies what would you suggest ? Also what is the difference between the E-Z Lube and the standard hub assembly? Would the E-Z lube assembly work in my application? Thank you?