What Are The Bar Dimensions Of The Rackem Fitz-All Enclosed Trailer Ladder Rack Part # RA-28

Question

Question:

Was wondering the wall thickness and tubing dimensions on the RA28 racks please! Thanks :

asked by: Murray

0

Expert Reply:

The dimensions of the Rack'em Fitz-All Enclosed Trailer Ladder Rack part # RA-28 are as follows:

The square bars used on this rack are 2" long X 1" wide X 3/16" thick.

I have attached both an installation and review video of this rack for you.

expert reply by: Conner L

0

Answer 1

Yes, this Rack em Fitz-All Enclosed Trailer Ladder Rack, part #RA-28, is made of aluminum and uses stainless steel screws. You may also be interested in purchasing Rack em Load Stop for Ladder Rack, part #RA-28-S. I attached installation…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Jaime, yes you can replace your 25-1/4 inch 3,500 lb axle leaf springs with a 5k rated axle spring like the part #e44SR. This will increase the suspension's weight capacity and might make the ride quality a little rougher but it would fit…

view full answer...

Answer 6

Hey Jim! The Taskmaster and Westlake tires, like the Taskmaster ST235/75R15 Off-Road #TA45RR and Westlake ST235/75R15 Off-Road #WST54FR you were looking at, are made in China. A lot of people tend to shy away from trailer tires made in China but…

view full answer...

Answer 7

Hey Kevin thanks for your question. There is not much downside to going with the 5,000 lb springs instead of the 3,500 lb. A higher rated spring may make the ride a bit more "chunky" at times, since the spring would not flex as…

view full answer...

Answer 8

Hey Tanya, it looks like both the Replacement Jack Screw and Nut Kit for Bulldog Topwind Trailer Jacks with 10,000-lb Lift Capacity BD500250 you're looking and the Replacement Jack Screw and Nut Kit for Bulldog Sidewind Trailer Jacks with…

view full answer...

Answer 9

We have several exterior ladders that could potentially work for you and your trailer. Take a look at #LA-401. This ladder is 99-1/2 inches tall. It may require a little modification depending on the design of your trailer but it would work. I have…

view full answer...

Answer 10

The weight capacity for Rackem Fitz-All Enclosed Trailer Ladder Rack part #RA-28 at a 7 ft width is 400 pounds. These racks are designed for fiberglass ladders, if you need more capacity another set can be added to spread the weight out more.

view full answer...

Answer 11

The 4-Leaf Double-Eye Spring #e44SR is our closest leaf spring to the Dexter 072-078-00 which we do not carry. Each of these springs is the same 25-1/4" from eye to eye but are rated for 2,500lbs per spring versus the 2,200lbs you are…

view full answer...

What Are The Bar Dimensions Of The Rackem Fitz-All Enclosed Trailer Ladder Rack Part # RA-28

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching