Replacement Hubs and U-Bolt Kit for 3,500 Pound Lippert Axle # LC35212150

Question

Question:

I have a LCI axle which has a broken hub and looking for a replacement. In addition I need new u bolts and lower spring plate. The axle info is as follows: LC35212150 NV# 212150 FBA-LCI35-SB-64-NOSS-L The bolt pattern is 5 x 5 Any help would be appreciated

asked by: Hans B

1

Helpful Expert Reply:

From my research your axle is a 3,500 pound, 2-3/8 inch diameter axle and since you have a 5 on 5 bolt pattern you likely have bearings # L44649 and # L68149. You'll want to verify this is correct with your current bearings.

If this is the case for a hub and drum assembly I recommend # AKHD-550-35-EZ-K which is for E-Z Lube axles with a zerk fitting. If you have standard axles use # AKHD-550-35-K instead.

If you only need idler hubs use # AKIHUB-550-35-EZ-K with E-Z Lube axles and # AKIHUB-550-35-K with standard axles.

All the hubs have a 5 on 5 bolt pattern and are for 3,500 pound axles.

For the u-bolts and plates you'll need U-Bolt Kit # APUBR-1.

expert reply by: Charles S

1

Answer 1

Typically the axle diameter is a good way to determine capacity but with the capacities being as close as your they could be the same diameter. A 3,500 lb axle should be 2-3/8 inches in diameter. You can also check the plate up near the coupler of…

view full answer...

Answer 2

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

I looked up the information on your TDE 46205 Hubs and found a couple of great replacements for you. The one you pick will depend on the number of wheel studs you have. For 5 wheel studs use the etrailer Trailer Idler Hub Assembly for 2,000-lb E-Z…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 12

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...

Replacement Hubs and U-Bolt Kit for 3,500 Pound Lippert Axle # LC35212150

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching