What Size Are The Kodiac Ceramic Brake Pads # K250CP?

Question

Question:

I have tri axel with 15inch wheels and do not know what size to get for replacements. If I get the 8000 pound does that mean 8000 times 3 axels=24,000 pound breaking capacity for boat weight?

asked by: Steve M

0

Expert Reply:

The Kodiak Ceramic Brake Pads - 7,000 lbs to 8,000 lbs # K250CP in some ways is rated for the 8,000 lb axle braking. So it will give you braking on 3 axles rated for 8,000 lbs when you use 3 kits. These brake pads are not easy to specify dimensions, so I've attached a photo to help with measurements being of the backing plate not the brake material.

expert reply by: Jason S

0

click to enlarge

Answer 1

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do…

view full answer...

Answer 2

We do not have a Kodiak disc brake caliper cross reference to automotive calipers but for the brake pads there are cross referenced parts. If you refer to the linked image you'll see a partial list of cross-compatibility of brake shoes for…

view full answer...

Answer 3

According to my contact at Rockwell American the most common reason for the guide bolt sleeve bushing #K338RB to walk out of the caliper assembly is incorrect lubrication. You can refer to the linked photo that shows where to, and where not to, apply…

view full answer...

Answer 4

I attached a chart that has the automotive cross reference for the Kodiak disc brake pads part #K2250CP that you referenced under the yellow heading. Probably the easiest to look up would be 1982 to 1992 Chevy Cavalier.

view full answer...

Answer 5

For your Kodiak disc brakes you have on your trailer you are going to want to use Kodiak replacement brake pads. You will need to follow the link I attached to the right, select your brake capacity from the filters and the correct pads will be…

view full answer...

Answer 6

The Gen-Y replacement pin box you mention isn't RV specific, it's specific to the OEM pin box used on your 5th wheel toy hauler. Unfortunately, there is no existing reference that will tell me what pin box was used on a given 5th wheel, so…

view full answer...

Answer 7

According to what Progressive Dynamics recommends, the Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger #PD4560K18LS8 is the correct replacement for your WFCO WF-9960 converter.

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

What Size Are The Kodiac Ceramic Brake Pads # K250CP?

Product Page this Question was Asked From

Continue Researching