Can Bearing Buddies be Used on Utility Trailer

Question

Question:

Is there any reason not to put Bearing Buddies on a utility trailer?

asked by: Alex

1

Helpful Expert Reply:

As long as you find the correct Bearing Buddy fit for the hub for your utility trailer there's no reason not to. Only reason it wouldn't be needed is if you have EZ lube spindles that have a zerk grease fitting on the end of them.

In order to pick out the correct bearing buddy you will need know the pilot hole of your hub. To do this, remove the wheel and tire and remove the grease cap from the center of the hub. Usually it is a metal cap that is just lightly hammered into place. Use a screwdriver to pry off the cap.

Clean the grease off and measure the opening. I have included a video demonstrating the Bearing Buddy.

The Bearing Buddies # BB1980A-SS that you referenced are for hubs with a 1.98 inch hub bore.

expert reply by: Jameson C

1

Answer 1

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 2

In order to pick out the correct bearing buddy you will need know the pilot hole of your hub. To do this, remove the wheel and tire and remove the grease cap from the center of the hub. Usually it is a metal cap that is just lightly hammered into…

view full answer...

Answer 3

They are not the same. The Bearing Buddy #BB1980T-SS are threaded into place, and not driven in. If your hub bore is threaded, that's the model you'd need. If your hub bore is NOT threaded, you'd use part #BB1980A-SS. The difference…

view full answer...

Answer 4

Not all trailer axles have the EZ lube zerk fitting so what you have is totally normal. You can use a Bearing Buddy like you mentioned but we have found is that the Bearing Buddies make it too easy to add too much grease which then blows out the…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Can Bearing Buddies be Used on Utility Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching