Bearing Kit Recommendation for Dexter 3,500 lb Axle

Question

Question:

Do you sell rebuild kits for Dexter 3500 lb axles? From inner seal out to dustdust cap?

asked by: Chris

0

Expert Reply:

Sounds like you are looking for a bearing kit for a hub on your 3,500 lb Dexter axle.

Dexter 3,500 lb axles are very common. They might be the most common axle found on trailers actually. Because of that we know that they bearing kit you need is the # BK2-100 which includes the correct bearings and seal.

expert reply by: Jameson C

0

Answer 1

I was able to look up your previous order and find that your Dexter Axle came with the Inner bearing #L68149 and outer bearing #L44649. A great replacement kit for these bearing numbers is the #BK2-100, it will include the inner and outer bearing…

view full answer...

Answer 2

So the answer is yes, with your 2-1/2 inch receiver you will still be able to use the Thule T2 Pro XTR Bike Rack #TH83JV. You are correct, however, that the your standard hitch reducer sleeve isn't going to work, so what you will need instead is…

view full answer...

Answer 3

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 11

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 12

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Bearing Kit Recommendation for Dexter 3,500 lb Axle

Product Page this Question was Asked From

Continue Researching