Recommended 6000 lb Surge Brake Actuator For Disc Brakes

Question

Question:

My 7k actuator does not move backward to allow moving on to ball as I move lever upward, the claw moves forward as I move Lever upward. need new one Can this actuator be used with disc brakes, which I plan to install

asked by: Darrell

0

Expert Reply:

Yes, and for a compatible actuator, I recommend the Dexter Zinc-Plated Brake Actuator w/ Electric Lockout - Disc - Multi-Fit Ball - Bolt On - 7,000 lbs # T47457207K.

expert reply by: Jason S

0

Answer 1

Having the slightly larger main feed line of 1/4 inch is a a great idea for plumbing up your triple axle trailer. We have the HydraStar kit part #HS496-153 which is designed for that. This kit uses 1/4 for the main feed line to the first tee fitting…

view full answer...

Answer 2

What you are describing is a problem most surge brake setups have that do not have a reverse lockout feature. Since you said a solenoid problem it sounds like you have an electric reverse lockout solenoid like the part #T4748800 that is not working.…

view full answer...

Answer 3

The actuator you have is a Titan Model 60 so for a replacement drum brake master cylinder you'd need the #T4395100.

view full answer...

Answer 4

Thank you for the pictures! I sent them to my contact at Titan and he said that you have the Titan Model 60 but that it was installed inside of the trailer tongue instead of on top of the tongue as designed. He mentioned that you will be able to use…

view full answer...

Answer 5

It sounds like you have been testing this system quite a lot. There are several steps you can follow to trace where the problem is. First, you did not say if this is a new brake system with disc brakes and was upgraded from drum brakes. If that is…

view full answer...

Answer 6

To bleed the brake lines with your Demco Hydraulic Brake Actuator w/ Drop and Electric Lockout #DM8750311 you'll need to complete the following steps: 1. First raise the tongue of the trailer 4" to 6". 2. Loosen or remove two 5/16”…

view full answer...

Answer 7

I have attached a video for you to help you bleed the surge brakes and also given an explanation below. You want to top off the master cylinder and pump the fluid from the master cylinder. You can do this by unbolting the plate that holds the lever…

view full answer...

Answer 8

Sounds like your trailer has an electric reverse lockout which prevents the brakes of your trailer from applying so that you can back the trailer up. If now the brakes won't release after the issue you had with someone else backing up the trailer…

view full answer...

Answer 9

I attached a chart that has the automotive cross reference for the Kodiak disc brake pads part #K2250CP that you referenced under the yellow heading. Probably the easiest to look up would be 1982 to 1992 Chevy Cavalier.

view full answer...

Answer 10

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 11

The side of the Silicone Dust Boot #K225BSSI, that comes with the Rebuild Kit #KDBC225KIT, with the design on the outside ring needs to face in towards the piston while the other side should face the brake pad. I have attached a photo to demonstrate…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Recommended 6000 lb Surge Brake Actuator For Disc Brakes

Product Page this Question was Asked From

Continue Researching