Replacement Electric Drum Brakes for 2006 Fun Finder Travel Trailer

Question

Question:

Is the akebrk-35-sa the kit i need for a cruiser rv 06 funfinder ? how soon would i get it in ohio 44718 ? thanks Ralph

asked by: Ralph

0

Expert Reply:

There are about a dozen different travel trailers in the 2006 Fun Finder series so the best way to know which replacement brakes you need is to pull one wheel/tire and hub and measure the hub diameter and width. The 10-inch brakes you referenced, part # AKEBRK-35-SA, are rated for 3500-lb axles and fit 10 x 2-1/4-inch drums, a popular size on travel trailers like your Fun Finder.

These brakes are the self-adjusting type that, once installed and adjusted initially, will self-adjust as they wear. These are compatible with 13-, 14- and 15-inch trailer wheels. They use a 4-bolt mounting pattern so when you pull your one hub you can confirm your existing brakes mounting pattern. Either brake wire can be used for ground or hot. Be sure to make solid ground connection at the trailer frame to ensure good performance.

expert reply by: Adam R

0

Answer 1

The attachment bolts for a 5-bolt brake assembly like the part #AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 12

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Replacement Electric Drum Brakes for 2006 Fun Finder Travel Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching