Dimensions Of B&W Gooseneck Turnover Ball

Question

Question:

What is the dimensions of the shank of the ball 2 1/2 X 2 1/2 X 4 ?

asked by: Tyler L

0

Expert Reply:

The measurement of the Replacement Hitch Ball for B&W Turnoverball Underbed Gooseneck Hitches - 2-5/16" # BWGNXA2000 is 2-1/2 inches by 2-1/2 inches by 4 inches. The ball on top of this shank is 4-1/16 inches tall. The hitch pin hole is centered in the shank so it is exactly 2 inches on center from the bottom of the shank. I've attached a couple photos to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

If the shackle straps are within a 1/2" of what you normally had, say the 2-5/8" #115052 to 3-1/8" #TRSL313, you should be okay to install them. Just make sure that all of your shackle straps match though. If you are using the longer…

view full answer...

Answer 2

Trailer manufacturers don't usually keep a record of parts like these that they install at the factory, so I cannot be sure as to the exact length of the shackle strap that would have come originally on your trailer. With this in mind, a 3-1/8…

view full answer...

Answer 3

Thanks for your purchase of the Demco Recon Gooseneck-to-5th Wheel Trailer Hitch Adapter for Recessed Ball #DM8550046! To determine the correct height setting for this hitch (11-1/2", 12-3/4", or 14") you need to measure from the…

view full answer...

Answer 4

I have attached for you below a dimensional drawing of the Lippert 1621 5th Wheel Pin Box part #LC1191191 which was provided by Lippert. This gives a frame of reference for the height by measuring from the bottom of the skid plate to the top of the…

view full answer...

Answer 5

I checked with Air Lift and was able to find a wiring diagram for the Replacement Air Gauge for Air Lift Load Controller Compressor System #AL25194 and attached it to this page.

view full answer...

Answer 6

Only certain B&W Companion 5th wheel trailer hitches are compatible with Sidewinder pin boxes like the RP61412. Basically if it is a Companion that mounts in the 4 pucks of a factory prep package then it can be used with a Sidewinder. But if the…

view full answer...

Answer 7

If the surface on the inside of the drum where the shoe pads make contact isn't smooth then a brake shop may be able to turn the drums. If that surface or the surface where the magnet makes contact (called the armature surface) is discolored then…

view full answer...

Answer 8

Based on the 12,400-lb base weight of your 2016 Reflections 357BHS you should have the Equa-Flex Cushioned Equalizer #LC279688 which works with 6K to 8K axles. The wet bolt to use is part #LC126238; you will need 7 for each side of the trailer, so 14…

view full answer...

Answer 9

I do have a couple possible solutions for raising your pontoon trailer, however increasing the shackle strap size will not be your best option. A more efficient way for raising the suspension on the trailer will be to use longer hangers. Unlike…

view full answer...

Answer 10

Thanks for the picture! Since your new 2021 Silverado 2500HD High Country has higher bed sides causing the pin box to make contact when turning the only option is going to be going with an 5th wheel to gooseneck adapter that is taller. For example…

view full answer...

Answer 11

For your 2020 Ford F-350 with the factory puck system, your best option will be with the B&W Ball and Safety Chain Kit #BWGNXA2061. The hitch ball included with this kit, which is designed to drop right into that center puck on your F-350, is the…

view full answer...

Answer 12

You can definitely use the MORryde suspension bolts if that's what you're wanting to use. The correct kit depends on what your trailer is currently equipped with and how long your shackle straps are (see attached photo of where to measure).…

view full answer...

Dimensions Of B&W Gooseneck Turnover Ball

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching