Recommendation for a Flood Light Intended for Outdoor Use

Question

Question:

Before I order, I want to make sure the S072 Custer is a flood type light and is for outdoor use. Thanks!

asked by: Vic

0

Expert Reply:

The Custer High Performance Utility Light, # S072, can be used for outdoor applications, such as to illuminate a truck bed. It will cover an area like a truck bed. This light works on a 12 volt system and uses a 55 watt H3 halogen bulb. A better option for a flood light would be # TL35FS, which can be used outside. Or you can use # TL46FS.

expert reply by: Michael H

0

Answer 1

If you want the highest light output for a given power input, then I suggest you go with LED-type lighting. LED lights will cost more up front, but they provide roughly 10-times the efficiency of standard incandescent lights, generate less heat and…

view full answer...

Answer 2

The 3" x 5" Rectangular Tractor and Utility Light w/ Flood Beam, 2 Wire Item #TL35FS uses a 12 volt, 55 watt H3 Halogen bulb #VX-SDH3. This is the whole bulb assembly. The bulb alone cannot be replaced since it is permanently mounted to the…

view full answer...

Answer 3

The Optronics Rectangular Tractor and Utility Light, part #TL46FS, you referenced, does have a hollow stud that the wires are run through to allow easier installation without the hassle of making another hole for wire routing. This light uses a 5…

view full answer...

Answer 4

I went out to the warehouse and pulled Optronics Rectangular Tractor and Utility Light #TL46FS to determine if the bulb is replaceable. Since it is an H3 bulb, it is attached to a base and it has a wire lead. The bulb itself is not replaceable but…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Recommendation for a Flood Light Intended for Outdoor Use

Products Referenced in This Question

Continue Researching