Can I Get Just the Rubber Cushions from the Replacement Cradles and Straps for Ladder Bike Rack

Question

Question:

Cradles and Straps for Surco 2-Bike Carrier Item # SPN449 Nothing is wrong with the cradles and straps I would like to replace the rubber cushions only.

asked by: Denny P

0

Expert Reply:

My contact at Surco said that the rubber cushions in the Replacement Cradles # SPN449 do not come separately. You will need to get new cradles so that you have the rubber part to protect your bike(s).

expert reply by: Jon G

0

click to enlarge

Answer 1

The Replacement Cradles and Straps for Surco 2-Bike Carrier #SPN449 that you referenced is a frame cradle and strap sold in pairs. So if you ordered a quantity of one you'd get two cradles and two straps.

view full answer...

Answer 2

If you have the version of the Surco 2 Bike Carrier for Vans and RVs #SP501BR that has rivets on the bottom of the arms of the rack they will need to be drilled out to remove as that's only way to remove rivets.

view full answer...

Answer 3

I went to the warehouse and measured the Replacement Cradles and Straps for Surco 2-Bike Carrier, part #SPN449. I attached a photo of the cradles with the dimensions shown. The cradles fit a 1 inch frame and the width of the cradle at the place where…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 8

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 9

Most critical to trailer tire performance and durability are 1) proper inflation 2) observance of the tire's rated load capacity and 3) observance of the tire's speed rating. If either of these factors is off the mark then the tire will tend…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Can I Get Just the Rubber Cushions from the Replacement Cradles and Straps for Ladder Bike Rack

Product Page this Question was Asked From

Continue Researching