How Many Velcro Fasteners are Included in Replacement TruXedo Shur-Bond Velcro Brand Fastener

Question

Question:

do you get one velcro strip or two when you order? this part?

asked by: Wesley P

0

Expert Reply:

The Replacement TruXedo Shur-Bond Velcro Brand Fastener # TX1115174 referenced in your question includes 2 Velcro Brand fasteners. It also includes 3 drive rivets which will be used for the Original Edge application. These will replace the fasteners on TruXedo Lo Pro QT or Original Edge tonneau covers.

I have attached a short video review of this product so you can see exactly what all is included.

expert reply by: Chris R

0

Answer 1

I went to our warehouse and took a look at the Replacement Header Seal for TruXedo Lo Pro QT, part #TX1704787. You will need to remove the seal you currently have by removing the plug on the end of the header. You may need to use something like a…

view full answer...

Answer 2

We do have the slide-in strips for 6-1/2 foot beds you are looking for; you will need the Replacement TruXedo Shur-Bond Hook-And-Loop Fastener Strips #TX1117876 which is 80 inches long.

view full answer...

Answer 3

The two different ratings you see are the WLL (working load limit) and the maximum load strength (break strength). WLL pertains to the capacity that you want to take into consideration under normal usage. The max break strength however, is the…

view full answer...

Answer 4

The TruXedo Shur-Bond Replacement Velcro #TX1115174 does fit the Lo Pro QT tonneau covers but measures more than 1-inch wide; it is 1-5/16-inches in width and 80-inches long. This slides into the cover's rail. We also have a screw-on Velcro…

view full answer...

Answer 5

For your short bed truck that has a Truxedo Lo Pro QT you would want the part #TX1115174 for replacement Velcros strips.

view full answer...

Answer 6

I went ahead and did some research, and I discovered that the replacement tarp depends on what model of TruXedo cover you have on your 2008 Toyota Tacoma's 5-Foot Bed. From my research, it is possible that you have one of three different covers.…

view full answer...

Answer 7

The Craftec Hatch-Style Tonneau Cover, part #352128 is a one-piece lightweight tonneau cover, and has two hidden latches at the rear so you will not have a problem with it flapping in the wind when installed on your 2000 Dakota. The tonneau cover…

view full answer...

Answer 8

I have exactly what you need for the TruXedo Lo Pro QT Soft Roll-up Tonneau Cover part #TX555901 on your 2007 Toyota Tacoma. The correct replacement clamps for this tonneau cover are the Replacement Clamp Assembly for TruXedo Lo Pro QT and Edge…

view full answer...

Answer 9

The part number on that sticker in your photo refers to the tensioning device, but luckily that narrowed things down enough to determine that the #TX1115174 Velcro strip is the correct replacement for you. It's longer than you actually need, but…

view full answer...

Answer 10

We carry so many varients of tonneau covers for the different vehicles. The options we carry for your 2005 Toyota Tacoma would be the TruXport, Lo Pro or the Deuce 2. Of those three, we have one replacement tarp and that is the replacement tarp for…

view full answer...

Answer 11

I may have a solution for you, but it will be difficult to confirm a correct replacement TruXedo Tonneau Cover for your 2005 Toyota Tacoma without identifying information such as a model number. I do show a few TruXedo Tonneau Covers that are custom…

view full answer...

Answer 12

Yes, to replace the rail end caps for the TruXedo Lo Pro Tonneau Cover #TX555901 on your 2006 Tacoma you will need part #TX1118097 for the Right Side and #TX1118096 for the Left Side. These are direct replacement parts and will work perfectly with…

view full answer...

How Many Velcro Fasteners are Included in Replacement TruXedo Shur-Bond Velcro Brand Fastener

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching