How To Replace The Header Seal On TruXedo Lo Pro Soft Roll-Up Tonneau Cover

Question

Question:

Im purchasing a header seal for the tailgate end of my Truxedo lo pro cover to replace the original thats deteriorating, are there instructions on how to replace the existing seal properly?

asked by: Jack F

0

Expert Reply:

I went to our warehouse and took a look at the Replacement Header Seal for TruXedo Lo Pro QT, part # TX1704787.

You will need to remove the seal you currently have by removing the plug on the end of the header. You may need to use something like a screwdriver and a rubber mallet to gently tap the seal at an angle to remove it. Then just simply slide the replacement seal in the groove and replace the end cap and you should be good to go.

expert reply by: Jeffrey L

0

Answer 1

We do have the exact part you are looking for to replace the bulkhead seal - also called the header seal - for your Truxedo Lo Pro tonneau cover. What you need is the Replacement Header Seal for TruXedo Lo Pro Soft Roll-up Tonneau Cover #TX1704787.

view full answer...

Answer 2

Thanks for providing that number/date code! The correct replacement tarp for your TruXedo Lo Pro soft tonneau cover is part #TX577601-CVR. Your cover uses the same seal at the front of the bed and at the tailgate. That replacement part is…

view full answer...

Answer 3

The correct replacement bulkhead weather seal for your TruXedo Lo Pro Cover is the Replacement Header Seal for TruXedo Lo Pro Soft Roll-up Tonneau Cover #TX1704787. This seal measures 5-1/2' long and 1-1/2" wide.

view full answer...

Answer 4

Could you get me pictures of your tonneau cover so that I can identify it possibly? And which exact seals do you need?

view full answer...

Answer 5

Yes it will; the Replacement Bulkhead Seal for TruXedo Lo Pro or TruXport Tonneau Covers #TX99FR will indeed stick to your spray-in bed liner. I have added a link below to a video review for you to check out as well of the Replacement Bulkhead Seal…

view full answer...

Answer 6

I was able to have a warehouse measure the Replacement Corner Weather Seal #TX1703568 you were looking at and they measure 3/8" thick and 3-1/2" across as you can see in the included diagram.

view full answer...

Answer 7

Tonneau covers and ladder racks can be compatible with each other when they do not use the same mounting points on the truck bed rails. Both tonneau covers and ladder racks can mount either inside the bed rails or on top of them. As an example, the…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

How To Replace The Header Seal On TruXedo Lo Pro Soft Roll-Up Tonneau Cover

Product Page this Question was Asked From

Continue Researching