Mounting Hole Dimensions Of The Dutton-Lainson Hand Winch Part # DL15440
Question:
are the mounting holes the same on a DL15440 as they are on a shelby model 5470A
asked by: Michael N
Expert Reply:
I do have the mounting location dimensions for the Dutton-Lainson Hand Winch part # DL15440 however, the Shelby Hand Winch part # 5470A is no longer available and as of October of 2016, SHELBY has gone out of business. I called my representative at Dutton-Lainson and unfortunately they were not able to provide me with compatibility information for Shelby winches.
The mounting hole locations for the Dutton-Lainson Hand Winch are as follows. The distance from the upper most hole to bottom hole is 4-7/8". The second most lower hole is 1" above the the lowest hole. The large oval shaped holes located at the bottom left and right hand corner are 3-1/4" from the two middle mounting holes. These two middle holes are 3" apart.
I have attached a picture of these dimensions for a more exact illustration.
Product Page this Question was Asked From
Dutton-Lainson Hand Winch - TUFFPLATE Finish - 2 Speed - Direct Drive - 3,200 lbs
- Trailer Winch
- Standard Hand Winch
- Boat Trailer Winch
- Utility Winch
- Extra Heavy Duty
- Standard Hand Crank
- Two Speed Winch
- Wire Rope
- Polyester Strap
- Dutton-Lainson
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: boat trailer winch trailer winch
- Video: Fulton Trailer Winch - Standard Hand Winch - F142418 Review
- Video: Dutton-Lainson Trailer Winch DL24249 Review
- Shop: Fulton XLT 2-Speed Trailer Winch with Heavy Duty 20' Strap - Zinc - 2,600 lbs
- Shop: Fulton High-Performance 2-Speed Trailer Winch with Handbrake - Cable Only - Zinc - 3,700 lbs
- Shop: Buyers Products 3/8" x 35" Class 4 Trailer Safety Chain w/ Clevis Hook - 30 Proof
- Shop: Buyers Products 3/8" x 35" Class 4 Trailer Safety Chain w/ 1 Clevis Hook - 43 Proof
- Search Results: trailer winch
- Search Results: safety chain
- Search Results: trailer safety chains
- Q&A: Boat Trailer Winch to Replace Old Shelby 5470A Winch
- Q&A: Recommendation for Replacement Shelby 5470A Winch with Large Drum Storage Capacity
- Q&A: Trailer Coupler is Stuck on Hitch Ball and Will Not Release
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: 25580
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Q&A: What is the Difference Between Load Range C and D ST175/80D13 Trailer Tires
- Article: Most Popular Wheel Bearings
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Search Results: safety chains
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Shop: Trailer Wiring
- Q&A: How to Determine the Size of a Trailer Hub Assembly for Replacement
- Shop: Brake Controller
- Article: Trailer Tire Sizing
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Search Results: fender
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
on Trailer Winch
