Is Shank of the Roadmaster High-Low Adapter # RM-076 Solid or Hollow

Question

Question:

Does this use tube or solid bar for the hitch ? I have an anti-rattle and it is the type that goes inside the tube. If this is tube and not solid I will order. I have seen pictures of both styles with this Blue Ox part number. Thanks

asked by: Chad

0

Expert Reply:

The shank of the Roadmaster High-Low Adapter # RM-076 is hollow so your anti-rattle device that is designed to fit a hollow shank will fit it and work well.

expert reply by: Jameson C

0

Answer 1

The length of the lower bar, pin hole to pin hole, is 10 inches.

view full answer...

Answer 2

When you're flat towing a vehicle, you want the tow bar to be within 3 inches plus or minus of level. If you're outside that range, you can use a High Low adapter to get you in range. Ideally, you'd be as close to level as possible, but…

view full answer...

Answer 3

When hooking your vehicle up to the RV you want the tow bar to be in what is called the "Safe Zone", which is 3 inches above or below level (see attached image). With base plate tabs that are 6 inches below the hitch on your RV you will…

view full answer...

Answer 4

I have a great solution for you. I confirmed with Curt that they do not have a tongue weight rating for the Curt High-Low Adapter for Tow Bars - 2" Hitches - 4" Rise/Drop - 8" Long #C59KR because this adapter is recommended to use for…

view full answer...

Answer 5

It sounds like you are looking for a high-low adapter like the Roadmaster High-Low Adapter for Tow Bars - 2" Hitches - 6" Rise/Drop - 6K GTW, 200 lbs TW #RM-076 to get your cargo carrier away from your exhaust pipe. This type of adapter…

view full answer...

Answer 6

For your 2007 Chevrolet HHR, the base plate you'll need is the Blue Ox Base Plate Kit #BX1692. Since this is a Blue Ox base plate and you're using a Roadmaster tow bar, you're also going to need the adapter #RM-031 to be able to use the…

view full answer...

Answer 7

The Curt High-Low Adapter #C59KR should work for giving you ground clearance for your cargo carrier. The measurement from the shank hitch pin hole to the back end of the top receiver is 5-1/2", which should be enough clearance for your bumper.…

view full answer...

Answer 8

Yes, the Curt High-Low Adapter for Tow Bars item #C59KR can be used with the Roadmaster Falcon All Terrain, Non-Binding Tow Bar item #RM-522. The high-low has a maximum weight capacity of 7,500 lbs.

view full answer...

Answer 9

For a first time flat tow all the information and requirements can seem overwhelming but lets go step by step and see how simple it and safe it actually is. First you need a base plate. This offers a secure mating/connection point to your vehicle. I…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Is Shank of the Roadmaster High-Low Adapter # RM-076 Solid or Hollow

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching