What is the Overall Length of Trailer 2k Hub Assembly 8-91-05UC1-EZ

Question

Question:

can you provide the is the overall length of part # 8-91-05UC1-EZ as shown in the included picture. Thanks

asked by: Jay

0

Expert Reply:

I went out to the warehouse to measure trailer hub # 8-91-05UC1-EZ for you. The overall length is 4-3/16 inches.

expert reply by: Michael H

0

click to enlarge

Answer 1

If the hub that was on your trailer axle previously had 8-91A stamped on the back of it your spindle should require inner and outer bearings of #L44649 like you used. The part #8-91-05UC1 SHOULD be an exact replacement. However we need to double…

view full answer...

Answer 2

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 3

To get the correct hubs for you, I need to have more information. You can either pull a hub and look at the face of the inner and outer bearing for the number printed on each bearing. If you don't want to pull the grease seal then the diameter of…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

To find the correct hub for your boat trailer there are a couple things you need to know. First, you said the bearings you have are 07100. In my research I found that the 07100 bearing has an inner diameter of 1.000 inch. We have a bearing that…

view full answer...

Answer 6

You are needing our Trailer Idler Hub Assembly #AKIHUB-440-2-G-1K. It is identical to the Trailer Idler Hub Assembly #AKIHUB-440-2-G-2K that you have on hold only it has the #L44643 Bearings that you need.

view full answer...

Answer 7

A non-tapered spindle with a 1.00" diameter will use an #L44643 inner and outer bearing, so you'll want to use the Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized #AKIHUB-440-2-G-1K, which have a 4 on 4 bolt pattern and…

view full answer...

Answer 8

The #AKIHUB-545-2-G-2K uses #L44649 bearings with an inner diameter of 1.063" and also has a 5 on 4-1/2 bolt pattern. Since you need #L44643 bearings with an ID of 1" and a 4 on 4 bolt pattern the correct part would be the Trailer Idler Hub…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

What is the Overall Length of Trailer 2k Hub Assembly 8-91-05UC1-EZ

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching