What is the Width of the Grease Seal part # GS-2250DL

Question

Question:

Could u please tell me the width of Axle seal # GS-2250DL I have i.d. and O.D. measurements Thanks

asked by: Dave C

0

Expert Reply:

The width of the Grease Seal part # GS-2250DL that you referenced is .387 of an inch.

expert reply by: Jameson C

0

Answer 1

We do not carry the Vortex hubs made by Tie Down Engineering. Unfortunately because of this, I don't really know how to assist with troubleshooting the hubs themselves as they are designed to seal out moisture and debris, yet are obviously…

view full answer...

Answer 2

Replacement trailer bearings (and races and seals) are most easily identified by using the part numbers stamped or molded into the original parts. The linked photo shows the typical placement and appearance of these part numbers on bearings, races…

view full answer...

Answer 3

There actually is no real difference. They have the same dimensions, fit the same applications, and are both double lip seals. Our part number for the 10-36 is the #RG06-070.

view full answer...

Answer 4

It took a bit of cross-referencing, but I found that the 10-10 grease seal, part #RG06-090 is the correct replacement for the Al-KO 568862 seals. You can confirm this by checking the ID of the hub bore where the seal would sit. The ID should be about…

view full answer...

Answer 5

Yes, the TruRyde Electric Trailer Brake Kit #TRU96FR will fit the 7,000lb Dexter axles on your 2020 Grand Design Solitude 375. We do also have the Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-464-465 if you prefer to keep the axle components…

view full answer...

Answer 6

Since we know your 2015 Jayco HT 27.5RLTS has 5,200 lb axles the correct bearing kit would be the #BK3-310 which comes with the correct bearings, races, seal and tang washer. To pick out replacement shoes I would need to know what brand assemblies…

view full answer...

Answer 7

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 8

We have many styles and sizes of trailer wheel lug nuts shown on the linked page. These are offered in either 60-degree or 90-degree coned profile, in zinc, chrome or stainless and for four different wheel stud diameters. Just click on the feature to…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

What is the Width of the Grease Seal part # GS-2250DL

Product Page this Question was Asked From

Continue Researching