Install Instructions/Video for Timbren Kit on a 2001 Ford F-250 4WD

Question

Question:

can you email me a set of instructions for installation of timbrens on a 2001 ford f250 4x4

asked by: Jason G

0

Expert Reply:

The Timbren kit you need for your 2001 Ford F-250 4x4 is the part # TFR250SDE which I attached a link to the install instructions plus a link to a video that shows our installers installing the kit on a 2002 Ford F-250 just like yours.

expert reply by: Jameson C

0

Answer 1

On your 2005 Chevrolet Express Van with the 7-wire trailer harness you will need to use a circuit tester like the #PTW2993 and test the function of each wire to know where to connect to the 7-wire outlet. I am sending a link with a picture of a 7-way…

view full answer...

Answer 2

Attempting to wire a 4 pole like the #18002 into the taillight system of your 1999 Express won't work, as you've found. The 1999 Express uses what is referred to as a separate or a 3 wire taillight system, where the running lights, turn…

view full answer...

Answer 3

The benefits of an Equal-I-zer hitch over the e2 is primarily the improved 4-point sway control of the Equal-I-zer. The 4-point sway control utilizes steel on steel friction at the arms as well as in the hitch head to stop sway. The e2's 2-point…

view full answer...

Answer 4

The Timbren Rear Suspension Enhancement System #TTORTUN4 that you referenced has a pretty straightforward and simple installation process. It just requires you to loosen the axle U-bolts and remove the factory bump stops on the truck and replace them…

view full answer...

Answer 5

On the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger #PD4045KA you need to verify that the converter/charger is set to the appropriate battery type that it is charging. It is common for the converter to get warm and the fan…

view full answer...

Answer 6

The Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 45 Amp #PD4045KA is the replacement we have for your unit. It is larger because it also is the panel and is 12-1/4" long x 8-3/4" tall x 7-1/4" deep…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...