Grease Cap PLug Needed for E-Z Luge Grease Caps

Question

Question:

Hi - just curious - are there bearing covers available for the Timbren hubs? the little rubber covers that go on the outside of the hub. Thanks!

asked by: Michael

0

Expert Reply:

If you are talking about the Grease Cap Plug for E-Z Lube Grease Caps, the part that you are looking for is # RG04-010 which comes in a quantity of 2.

expert reply by: Jon G

0

Answer 1

Standard tapered trailer wheel bearings are recommended to be re-packed with fresh bearing grease about every year or every 12,000 miles under normal use. In certain conditions this interval could be shorter, such as if you routinely tow the trailer…

view full answer...

Answer 2

When you are assembling the hub components you want to make sure you fill every space of the bearings with grease like part #L11465. To make this easier you can use a bearing packer like part #L70025. If you do not have one, you can use a grease gun…

view full answer...

Answer 3

Yes,the RG04-010 Grease cap plugs fit the Dexter E-Z Lube grease caps on the Dexter E-Z Lube axles.

view full answer...

Answer 4

I can help you with greasing up your EZ Lube Axle. First thing I would check would be that the grease is not coming out of the back of the axle through the seal. If this is the case you will need to replace the seal. Our tubes like #L11390 have 14…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Grease Cap PLug Needed for E-Z Luge Grease Caps

Product Page this Question was Asked From

Continue Researching