Replacement Fulton Trailer Jack for Sled Bed trailer

Question

Question:

I can not seem to find any bolt on replacement the existing Fulton is mounted to a 2 7/8 by 6inch tongue

asked by: Tony R

0

Expert Reply:

We have the Fulton Marine Jack # HD50000101 which will fit trailer's with a frame up to 6 inches.

expert reply by: Charles S

0

Answer 1

The mounting plate for the Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR has the following dimensions. I have included an image to show the measuring points. The holes are spread 5-1/2" wide with the vertical holes separated 1" on the…

view full answer...

Answer 2

The blue wire on a trailer is typically the output wire to the electric brake assemblies. If this is the case on your trailer then the wire should only have power when you are hooked up to the tow vehicle and are applying the brakes, either by…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

Replacement arms are available for the Roadmaster EZ5 Base Plate Kit #RM-521569-5 for your 2015 Honda Fit with the part #RM-ARMS. When the original base plate brackets and arms were manufactured, they were made as one part. To be sure that the new…

view full answer...