Sway Control Bracket to Fit 2-5/16 Inch Hitch Ball with 1 Inch Diameter Shank

Question

Question:

I need the metal plate with the trailer ball hole !inch dia. to sit on top of my Reese receiver. This kit has the top plate with the sway control 1 inch dia. ball,generally sold separately offset to right or left or the main 2 15/16inch trailer ball. The kit also has a bottom plate that bolts up to the top plater with bolts locking washers and nylon locking nuts. All I can find are the plates with a welded small ball head that mounts to the side of the trailer at the rear of the sway control arm. I have that arm as well as the bolt on trailer mount. I need the above kit from Husky complete with the small ball for the front mount of the say control arm.

asked by: J.Michael W

0

Expert Reply:

The sway control bracket you're looking for is # RP26003. This fits a 1 inch diameter hitch ball which you can use # C40007 for a 2-5/16 inch ball.

I've linked a video of the bracket being installed.

expert reply by: Charles S

0

Answer 1

Yes, Reese Sway-Control Bracket for 2" Ball Mounts - Class III and IV Item #RP26003 will work 2with a 2-5/16 inch ball provided that the shank of the ball is 1 inch in diameter such as Brophy hitch ball #SC30-C.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 10

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Sway Control Bracket to Fit 2-5/16 Inch Hitch Ball with 1 Inch Diameter Shank

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching