Plug-In Wiring Adapter to Install a Prodigy P2 Electric Trailer Brake Controller in 2017 Ram 1500

Question

Question:

What is the proper adapter to fit my 2017 Dodge Ram 1500 to my Prodigy P2

asked by: Bob V

0

Expert Reply:

The wiring harness to install a Prodigy P2 # 90885 brake controller in your 2017 Ram 1500 is # 3024-P. I've linked an install video for you too.

expert reply by: Charles S

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 5

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 6

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 7

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 8

There are a number of factors involved when converting a semi 7-way to an RV 7-way. Semis generally use a 7-pin round pin socket, similar to #PK11720. And RV style 7-way uses blades, like #PK12706. We do not offer any pre-made adapters to make this…

view full answer...

Answer 9

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...

Answer 10

From what I could find, it looks like the plug for a trailer brake controller on your 2023 Nissan Frontier is located in the same location as the 2022 model year. That is behind the side panel by the OBD connector and is likely pushed back into the…

view full answer...

Answer 11

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 12

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Plug-In Wiring Adapter to Install a Prodigy P2 Electric Trailer Brake Controller in 2017 Ram 1500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching