Can Tray # LC370785 Be Used For Battery Compartment on 2000 Holiday Rambler

Question

Question:

Would you recommend this for the battery compartment? I have a 2000 Holiday Rambler.

asked by: John

0

Expert Reply:

The Tray Assembly Kit, part # LC370785 is normally used in a cargo compartment on RVs to make it easier to load and unload cargo.

The tray assembly kit is designed for compartments that are at least 54-inches deep. The width of the tray is determined by the width of the compartment you are using it with. You will need 3/4-inch plywood to install the tray slides on.

I've attached the link to all your cargo compartment slide options to assist with sizes available.

expert reply by: Jeffrey L

0

Answer 1

For the MORryde RV Cargo Sliding Tray - 90" x 36", #MR38FR MORyde chooses to describe their function as a 60 percent extension, this indicates that 60 percent of the 90" tray is moved past the starting point for a stowed position.

view full answer...

Answer 2

I had our warehouse measure the MORryde Sliding Tray for RV Cargo Compartment #MR34FR you were looking at and the inside dimensions are 34-1/8" long x 16-3/4" wide so your 19" wide generator will not fit. You will need to step up to a…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

Thanks for the photo! For your Ram you currently have the Curt A20 #C16541 with the Adapter Rails #C16022. To fit this on your 2022 Ford F-350 Super Duty with the 8' bed and OEM package you can either use the Adapter Rails #C88KR or the Leg Kit…

view full answer...

Answer 7

We always recommend a sliding hitch with a 6', 6-1/2', or 6-3/4' bed in order to have enough clearance to prevent the nose of the trailer from coming into contact with the cab of the truck. With Companion fifth wheel hitches you can…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The Furrion camera system we have is a closed system and would not be compatible with the in-dash display so you would need to purchase GM's camera system to be able to connect to your display instead of having another monitor. If you do end up…

view full answer...

Answer 10

The Curt A20 5th Wheel Trailer Hitch for Chevy/GMC Towing Prep Package #C84FR you referenced weighs 153 lbs. What's interesting though is that payload is the weight capacity of the truck bed but this hitch attaches actually to the rail kit of the…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...