Hub Recommendation with Bolt Pattern 5 on 4-1/2 inch and Fits Spindle with Diameter 1-1/6 inch

Question

Question:

Axle diameter for hubs .i have a 11/16 axle dis .i need a 5 lug on 4 1/2 centers

asked by: Lee

0

Expert Reply:

The hub you need is the part # AKIHUB-545-2-2K as it has a bolt pattern of 5 on 4-1/2 inch, is designed for a spindle that has diameters of 1.06 inches where both bearings fit.

expert reply by: Jameson C

0

Answer 1

I reached out to the manufacturer of the Detail K2 Mighty Multi A-Frame Utility Trailer #K2MMT5X7 and if you have a VIN that begins with L1 then you will use the Trailer Idler Hub Assembly for 2,000-lb Axles - 8" to 12" Wheels - 5 on 4-1/2…

view full answer...

Answer 2

You didn't list your tire size, but if you have a 185/80D13 like the part #AM3S331 that you mentioned I have a better recommendation I can make. You would be better served with the part #TTWTRTM1758013C as it is a radial tire that has an 81 mph…

view full answer...

Answer 3

The particular bearing buddy you reviewed, part #BB1781, fits a hub bore of 1.781 inches and an outer bearing number #LM11949. Trailer and camper manufacturers may use different components in their products from one production run to another, so the…

view full answer...

Answer 4

First, I'd recommend confirming your wheel bolt pattern. Take a look at the FAQ article I've linked for you. Chances are, your wheels have a 5 on 4-1/2 inch bolt pattern but I recommend confirming it. You'll want to choose a tire whose…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Hub Recommendation with Bolt Pattern 5 on 4-1/2 inch and Fits Spindle with Diameter 1-1/6 inch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching