Which Hitch Receiver Hole Should Auto-Pin On Thule T2 Bike Carrier Shank Be Used With

Question

Question:

I have a Draw Tite hitch model number 75299 and a Thule Bike Carrier model T2 Pro XT. I have no experience with this and was wondering what hole in the hitch the smaller or larger hole do I the Auto Pin in? Thank you for any help you can give me.

asked by: Jennifer W

1

Helpful Expert Reply:

You will need to insert the shank of your T2 bike carrier in the Draw-Tite receiver until the auto-pin fits in the larger hole.

You do not use the smaller hole at all.

expert reply by: Jeffrey L

1

Answer 1

I can definitely dispel any confusion you have. Like the video, I confirmed with Kuat that the total length of the Kuat Hitch Receiver Reducer Sleeve - 2-1/2" to 2" Hitch #KU93VR is 6-1/4" long. I went ahead and attached a diagram that…

view full answer...

Answer 2

You are on the right track. The only way we have that will allow you to use the Thule T2 Pro Xtr Bike Platform Rack part #TH69TX with the 2.5" receiver tube opening on your truck would be with adapter. For this, I recommend the Brophy Hitch…

view full answer...

Answer 3

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I checked the manual and also reached out to Blue Ox to confirm this but found no notes and Blue Ox stated that the Blue Ox Base Plate Kit #BX1739 would be a compatible fit for your 2020 GMC Sierra 3500 (diesel). If you haven't picked out the…

view full answer...

Answer 10

On equalizer 013-105-04 in kit #K71-360-00 the eye center to eye center measurement is approximately 7-1/2 inches.

view full answer...

Answer 11

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 12

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Which Hitch Receiver Hole Should Auto-Pin On Thule T2 Bike Carrier Shank Be Used With

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching