Constant Voltage on 12V and Brake Controller Output Wire with Curt TriFlex Trailer Brake Controller
Question:
I have a Curt C24VVBrake Controller and a Curt 51515 harness installed in my 2014 Toyota Sienna. I plug a tester identical to the pollak PK12741 into my 7 pin socket and the 12v and bk lights both light up with the van ignition off and no brakes applied. I grab my volt meter and the 12v pin 1oclock position measures 12.2 volts. The 5 oclock pin trailer brakes measure 11.2 volts. I read in some of your other answered questions that a small amount of voltage is normal. 11.2 volts doesnt seem small to me. I cut the blue wire from controller plug harness 51515 and the 11.2 volts ped to 0. I thought for sure that my controller was faulty. I called Curt tech support and explained my findings in hope that they would honor the lifetime warranty. They told me that the 11.2 volts was normal, and I shouldnt worry. He further went on to say that the amperage is what matters, not the voltage at the plug. He lost me at that point, amperage isnt my thing. Can you please clarify this? I have to drive 100 miles to pick up my trailer, and dont want to have locked up brakes when I get there.
asked by: Trevor
Expert Reply:
When testing the wire functions after installing the Curt TriFlex Trailer Brake Controller # C24VV and Wiring Harness # C51515 in your 2014 Toyota Sienna, it is normal for both the 12V and brake lights on a tester to light up without actually activating the brakes. This is because the brake controller sends out a small trace current to look for a completed circuit. I have attached a demonstration video on a similar 7 Way Trailer Connector Vehicle Tester # C73NR that shows this right around the 1:10 mark.
The 12.2 and 11.2 volts you measured with your meter are normal and Curt calls this "dead voltage", which you can look at as more of a false reading because of how the Curt brake controllers work. When they told you that amperage is what matters here, they are referring to when the wires actually draw a current. An actual load is only going to be placed on the current when you press down on the brake pedal or use the manual override switch on the controller. This is what they are referring to when they talk about amperage as opposed to the small voltage that is constantly being shown on the tester or meter that you used.
Products Referenced in This Question
Universal Wiring Adapter for Curt Trailer Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Universal
- CURT
more information >
Curt 7-Way to RV Socket LED Circuit Tester - Vehicle End
- Electrical Tools
- Testers
- Circuit Tester
- Tow Function Tester
- CURT
more information >
Product Page this Question was Asked From
Curt TriFlex NEXT Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Troubleshooting Constant 12V Power on Blue Brake Output Wire with Curt Venturer Brake Controller
- Search Results: rv front mount hitch
- Shop: Base Plate for Tow Bar
- Shop: Blue Ox Base Plate Kit - Removable Arms
- Shop: Trailer Wiring
- Q&A: Curt Triflex Trailer Brake Controller Shows Power All the Time on Blue Wire
- Shop: Replacement Mounting Bracket for Draw-Tite Activator or I-Command Brake Controller
- Q&A: Connecting Brake Controller Wiring on 2019 Chevy Express Van 3500
- Shop: Vehicle Tow Bar Wiring
- Search Results: 118605
- Search Results: trailer harness
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Best 2016 Jeep Grand Cherokee Trailer Wiring Options
- Q&A: Installing a Brake Controller in a 2018 Winnebago Forza 34T
- Shop: Load Stops for Yakima HD Bar, JetStream, FlushBar, and RailBar Crossbars - Qty 4
- Search Results: yakima exo
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Choosing the Right Trailer Wiring
- Shop: Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Search Results: tow bar
- Article: How to Choose the Right Trailer Hitch Class
- Video: Blue Ox Patriot Portable Braking System Installation - 2022 Ford F-150
- Search Results: base plates
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Brake Controller
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: Choosing Between the Brake Buddy Select 3 and the Blue Ox Patriot Supplemental Braking System
- Search Results: 90160
on Trailer Brake Controller
