Which Harness is for Installing Brake Controller in a 2014 Ram 1500

Question

Question:

I have P3 with adapter for 2014 RM 1500. Which adapter do I need for 2009 Ram 2500 with factory 7-way? Ive attached photo of under dash area and I dont know which plug to use.

asked by: Charles M

0

Expert Reply:

I put an arrow on the picture you sent in that shows which of the connectors the # 3020-P needs to connect to.

expert reply by: Jameson C

0

click to enlarge

Answer 1

There are two color code standards that are used in the trailer world. The Hopkins 7-Way RV style connector and cable, #H20046, that you referenced uses the RV Industry standard color code which is as follows: White Wire - Ground Red Wire - Left…

view full answer...

Answer 2

You are correct that there is a green wire exiting the brake controller connector under the dash of your 2005 Jeep Grand Cherokee. The problem is that since your vehicle is not equipped with the tow package the wire is terminated somewhere inside the…

view full answer...

Answer 3

To install a brake controller in your 2006 Jeep Liberty with a factory 7-Way you will need to hardwire the wires from the back of the brake controller to the vehicle. This vehicle does not have a brake controller port that you can plug the brake…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 7

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 12

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Which Harness is for Installing Brake Controller in a 2014 Ram 1500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching