Hinge Mounting Hole Dimensions & Spacing Measurements

Question

Question:

I need to know the measurement of the holes on the square end of the unit, outside to outside and center to center

asked by: Barney K

0

Expert Reply:

I went to our warehouse and measured the Polar Polished Stainless Steel T-Strap Hinge # PLR3408-PS to get the dimensions you need.

The two holes on the square/door jamb end of the hinge are 3/8-inch in diameter. Their center-to-center hole spacing is 3-3/16-inches and their outside-to-outside spacing is 3-5/8-inches. I prepared a photo with these dimensions that is linked for you.

expert reply by: Adam R

0

click to enlarge

Answer 1

I would be happy to help you find the correct replacement door hinge for your 2000 Sooner Royale Horse Trailer, but I was unable to find any dimensions or information about the 03139010 hinge you mentioned. Based on the picture you provided it looks…

view full answer...

Answer 2

From the look of your picture I'm guessing you have the 180 degree Polar strap hinge part #2512. The entire strap from the hinge is about 12 inches long from the center of the pin and the holes are 3-5/8 inches apart on center. If this…

view full answer...

Answer 3

That will depend on the amount of brake axles your trailer has. . The 20 amp breaker like #9506P is for 1 and 2 axle brakes, and the 30 amp like part #38630 is for 3 and 4 axle brakes

view full answer...

Answer 4

If your 2005 Jeep Liberty has the factory tow package there will be a rectangular shaped connector under the rear bumper. I've attached a picture to show you what the connector looks like. If you find it you can install a 4-way and 7-way…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Hinge Mounting Hole Dimensions & Spacing Measurements

Product Page this Question was Asked From

Continue Researching