Is The Ball Mount Included With The Curt Class II Drawbar # C45520 For A 2003 Toyota Camry
Question:
Is Ball Mount D20/45520 Included in the price shown. This is for Hitch Model #12339 for 2003 Camry.
asked by: Ron A
Expert Reply:
Yes, the Curt Class II Drawbar, part # C45520, is included with the Curt Class II 1-1/4 Inch Hitch, part # 12339, for your 2003 Toyota Camry. It will also include the Curt Class I and II Pin and Clip, part # F-4. I am including a link to a video of this Curt hitch being installed on a 2003 Toyota Camry.
To complete your towing setup, you will also need the Tow Ready 2 Inch Hitch Ball, part # 19258, or the Tow Ready 1-7/8 Inch Hitch Ball, part # 19256 and the Tow Ready T-One Wiring Harness, part # 118308. See link at bottom of page of the installation instructions for the T-One wiring harness.
If you will be using the Curt hitch for a non-trailer load like a bike rack or cargo carrier you will need to use a stabilizing strap like the Curt Bike Rack Strap, part # 18050. It is required by the manufacturer (Curt) to give extra support to the hitch accessory. Failure to properly support these loads will void your hitch warranty from Curt.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 3 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 300 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Q&A: Can 12 Volt Power Be Run With a 4 Flat Trailer Plug?
- Q&A: Brake Switch Location to Install a Brake Controller on a 2004 International 4300
- Q&A: Where is the Brake Switch to Install a Brake Controller on a 4300 International Truck
- Article: Trailer Hitch Receiver Sizes
- Q&A: How Much Does the Head and Base Weigh for the B&W Companion 5th Wheel Trailer Hitch
- Article: Hitch Adapters and Extenders
- Q&A: Hitches For 2019 BMW X5 With Or Without M-Sport Package
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Wiring Diagrams
- Article: Best Bike Racks for Electric Bikes