Is the Install of the Draw Tite Hitch 76025 the Same Between 2012 and 2014 Honda Odysseys

Question

Question:

I have a 2012 honda odyssey. I was wondering if the draw tite 76025 hitch would install similar to the 2016 or 2014 video. One you add washers between the hitch and the car. The other you guys dont install the washers. Will this install on my 2012 the same as the videos? if so Which video should I follow Thanks

asked by: Todd G

0

Expert Reply:

The Draw Tite hitch part # 76025 that you referenced is a confirmed fit for your 2012 Honda Odyssey. It would install exactly the same as the video that shows the hitch installed on a 2014 Honda Odyssey. I checked the install instructions and there aren't any special steps between the two different years. 2012 and 2014 Odysseys are the same generation and the frame area where the hitch installs is the same between the two.

I attached a link to the video you mentioned as well.

expert reply by: Jameson C

0

Answer 1

To mount the Curt T-Connector Vehicle Wiring Harness item #C56378 to the Draw-Tite item #76025 you will want to use the No-Drill Mount Bracket item #18136 and the item #18144. This will allow you to install the 4-way farther down from the hitch…

view full answer...

Answer 2

I attached a link to the install video for the Draw Tite hitch part #76025 as well as a link to the install instructions for you to check out as well.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 11

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Is the Install of the Draw Tite Hitch 76025 the Same Between 2012 and 2014 Honda Odysseys

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching