Lippert 6k Trailer Axle Brake Assembly Recommendation

Question

Question:

Looking for replacement brake kits for my 2011 Keystone Raptor 361LEV triple axle. Tags on the axles are: Lippert 6000 lbs Serial # 045-001247603 NV # 139501 Would the AKEBRK-7-SA be the correct fitment?

asked by: Greg R

1

Helpful Expert Reply:

Yes, for your Lippert 6k axles the Brake Assemblies part # AKEBRK-7-SA that you referenced are a confirmed fit and would work well.

expert reply by: Jameson C

1

Answer 1

The HydraStar Disc Brake Kit item #HSE7K-TR1SO is designed for trailers with 7K axles and an 8 on 6-1/2" bolt pattern. This conversion kit would work great on your 42 1/2 foot travel trailer. If you need new hubs with the brake kit you will want…

view full answer...

Answer 2

I understand why it would seem confusing running the steel and rubber lines for disc brakes on your trailer that come in a disc brake kit like part #HSE7K-TR1. The steel lines are the main lines on the trailer and the rubber lines extend to the brake…

view full answer...

Answer 3

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 12

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...