Does SuperChips Programmer Flashpaq part SU4845 Fit 2008 Chevy HHR SS

Question

Question:

I bought a superchips programmer for my 2008 HHR SS but I could not get it to work. Does the Edge unit come with the program already installed? If so which unit should I purchase for this application?

asked by: Jim

0

Expert Reply:

For your 2008 Chevy HHR SS the Superchips programmer part # SU4845 is a confirmed fit and will give you a very noticeable increase of 47 horsepower and 55 ft lbs of torque.

You will need to update the programmer when you first get it, but it will work well on your vehicle.

expert reply by: Jameson C

0

Answer 1

We have the Superchips F5 programmer part #SU4845 which is a fit for your 2014 GMC Sierra 1500 with a 5.3 liter engine and is also approved for use in California. It can give you up to an additional 18 horsepower and 27 ft lbs of torque.

view full answer...

Answer 2

The Superchips programmer part #SU4845 that fits your 2013 Chevy Silverado with a 5.3 liter will give you up to 15 horsepower and 15 ft lbs of torque.

view full answer...

Answer 3

Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.

view full answer...

Answer 4

I checked your order notes and the leaf springs you bought last year were the part #e28SR which are for 5k axles. Since this is over the capacity of your axle failure would not have been caused by over loading the trailer assuming you stayed under…

view full answer...

Answer 5

The Dexter 072-078-00 is a 2,200 lb capacity leaf spring. You can use a higher capacity leaf spring, however it won't increase the capacity of your trailer as the axle is still rated for that max capacity of 4,400 lbs. My recommendation for a…

view full answer...

Answer 6

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement for…

view full answer...

Does SuperChips Programmer Flashpaq part SU4845 Fit 2008 Chevy HHR SS

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching