Will a PullRite SuperGlide 5th Wheel Hitch Fit B&W Custom Installation Kit

Question

Question:

Are theses rails compatible with the Pull-Rite SuperGlide 16k 5th Wheel Hitch?

asked by: Brian J

0

Expert Reply:

The SuperGlide hitch comes in 2 forms. The one labeled as an ISR will fit the B&W 5th wheel rails in custom installation kit # BWRVK2500. The ISR stands for industry standard rails. If it is not the ISR version then it will only fit the special mount by PullRite.

expert reply by: Michael H

0

Answer 1

If the Pullrite Superglide is an ISR style fifth wheel hitch which is designed for the rails that the Curt kit part #C16411-204 provides this will work. But there are two types of rails Pullrite designs their hitches for with one of them being for…

view full answer...

Answer 2

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 3

The auto-sliding 5th wheel hitches like the PullRite SuperGlide and the Demco Hijacker Autoslide 5th Wheel Trailer Hitch part #DM8550035 which we carry cannot be used with the Demco 5th Wheel Base Rails Adapter part #DM6140 or any B&W…

view full answer...

Answer 4

The MORryde Cushioned 5th Wheel Pin Box - Lippert 1621HD - 18,000 lbs Item #MR64VR is designed to replace your current Lippert 1621 HD pin box

view full answer...

Answer 5

If you have Timbren springs #TGMRYS4 then they bolt into place. There are 2 parts to each of these springs. One part is the spring itself which should come off easily once you remove the bolt up in the center. The other part is a short cylinder that…

view full answer...

Answer 6

For your 2017 GMC Sierra 1500 with a 6-1/2 foot bed we recommend using a slider hitch. I recommend the B&W Patriot 5th Wheel Trailer Hitch w/ Slider Item #BWRVK3270 and the B&W Custom Installation Kit w/ Base Rails Item #BWRVK2503. B&W…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Will a PullRite SuperGlide 5th Wheel Hitch Fit B&W Custom Installation Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching