How to Select the Correct Hub to Change Out a 4 on 9.44 Inch Bolt Circle Wheels with 5 on 4-1/2
Question:
I have an older trailer with 4 bolt 9.44 bolt circle Hubei and wheels. I want to upgrade to 5 x4.5 hub configuration so I can get better rims and balance the tires. 3500 pound axle with 10 drums. I have measured the axle diameters bearing and seal diameters and they match your 3500 pound spindle numbers and the bearing diameter specs. Will a standard 1750 pound hub and drum fit. I am concerned about the spacing of the bearings in the hub. Thx.
asked by: Matt
Expert Reply:
It sounds as if you have taken all of the correct measurements to determine the correct hub and drum assembly for your trailer. Normally the spacing of the bearings is not an issue, as long as the axle used on the trailer is not an Agricultural axle or a mobile home axle.
The Trailer Hub & Drum Assembly, item # AKHD-545-35-EZ-K, is designed to be used with the EZ Lube Spindle for 3,500 lb axle, item # TRU74FR. The dimensions of this spindle are as follows.
Seal diameter - 1.73 inches
Inner Bearing diameter - 1.38 inches
Outer bearing diameter - 1.06 inches
If the dimensions on your axle match these dimensions then the 1750 lbs # AKHD-545-35-EZ-K hub assembly should work fine on your trailer. If not let me know the measurements you have taken and we can try to find the correct hub and drum assembly for your trailer.
If you cannot come up with a hub and drum assembly that will fit your trailer we do have wheels to match your 4 bolt 9.44 bolt circle. I have added a link to all of the vintage replacement wheels that we carry for you to review.
Products Referenced in This Question
#84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Trailer Spindles
- EZ Lube Spindle
- 1-3/4 Inch Diameter
- Round
- For 3500 lb Axle
- TruRyde
more information >
Product Page this Question was Asked From
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Vesper Steel Modular Trailer Wheel - 15" x 5" Rim - 5 on 5 - Black
- Shop: Dexstar Vintage Steel Wheel w/ +5 mm Offset - 14" x 5-1/2" Rim - 4 on 9.44
- Shop: 6" Wide Continuous Hinge - 8' Long - 1/2" Pin Diameter - Steel
- Shop: Grease Seals 10-36 (pair)
- Shop: Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - White
- Search Results: electric tarp
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Hitch
- Shop: Loadstar ST205/75D14 Bias Trailer Tire with 14" Black Wheel - 5 on 4-1/2 - Load Range C
- Shop: Truck Bed Tailgate Assist
- Shop: Tailgate
- Search Results: bp01~301
- Search Results: 8~288
- Search Results: gorilla lift
- Search Results: 023~442~00
- Search Results: receiver tube
- Search Results: 25580
- Shop: Gooseneck Hitch
- Shop: Brake Controller
- Q&A: Converting From 4 On 9.44 to 5 On 5 Bolt Pattern
- Shop: Suspension Enhancement
- Q&A: How to Determine Weight Capacity of Trailer Axle
- Q&A: How To Determine the Weight Capacity For a Trailer Axle
- Video: Kenda Tires and Wheels - Tire with Wheel - AM3S451 Review
- Q&A: Can a Hub and Drum Assembly with a 4 on 9.44 Bolt Pattern be Replaced with a 6 on 5-1/2
- Shop: Trailer Wiring
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Q&A: New Brakes and Hubs for Old Holiday Rambler Trailer With 7,000 lb Axles
- Q&A: Replacement Hub Options To Upgrade from 4 on 9.44 Inch Bolt Pattern
- Article: Trailer Tire Sizing
on Trailer Hubs and Drums
