Hitch Tube Recommendation for Fabricating Hitch to RV

Question

Question:

I need help choosing a hitch for my 2010 Heartland Landmark Grand Canyon. We are planning to mount a hitch for kayaks 2 and bikes 2. It will be similar to the He will fabricate it himself. He is a welder/fabricator. Could you please help my choose?

asked by: Deb

0

Expert Reply:

If you are planning on having a crossmember welded to the frame of your trailer you would be best off just having the part # 41990 welded to the frame as that has the hitch opening already welded to it. Or we have the part # 41990-07 which has the hitch attached to drop brackets.

expert reply by: Jameson C

0

Answer 1

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 2

You were on the right track already with the #41990 for your 2010 Mitsubishi Fuso FE145. There are no custom fit hitches so a universal weld-on is the only option. We have the #41990-07 that comes with 7" brackets, the #41990-16 with 16"…

view full answer...

Answer 3

I have a solution for you that I can provide, but we aren't going to have a custom fit hitch to fit a vehicle like what you referenced. I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a service body…

view full answer...

Answer 4

We do have a couple Class V hitch options available for your 2020 F53 and I have 3 options listed below. These will all be rated to 16,000 pounds towing and 1,600 pounds of tongue weight and use a 2" receiver opening. They will all also fit a…

view full answer...

Answer 5

It sounds like you're asking about the deflection of the 2K Timbren Axle-Less Trailer Suspension #ASR2KHDS04, which Timbren has listed as 1-5/8" in the attached diagram - see the (r) label. If you are talking about something else please let…

view full answer...

Answer 6

I have a recommendation for you as the Bulldog Winch Hitch Mount Storage Bracket #BDW20154 is only designed to hold a winch when not in use. It does not have the structure required to operate a winch. For a 12,000LB Winch #BDW10040 you will need a…

view full answer...

Answer 7

We have many hitch options for a truck that has a lift gate, but very few of them are a simple bolt on custom application. Because the locations for attaching lift gates vary, you will need to use a weld on option like the Class V Universal Weld-on…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Brad, thanks a bunch for going ahead and getting all those measurements in advance. Based on the measurements you've given, the TorkLift GlowStep Revolution Uprising Steps w/ Booster Step #TL52SR will work perfect for your coach. These steps…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Hitch Tube Recommendation for Fabricating Hitch to RV

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching