Are Load Resistors Needed on a 2010 Nissan Rouge when Installing LED Blinkers

Question

Question:

I have a 2010 nissan rogue and i put 4 led blinkers. 2 in the back and 2 in the front, how many load resistors would i have to purchase? and can i get any load resistors or do i have to calculate the Oms and set it?

asked by: Daniel P

0

Expert Reply:

Yes, you will need a Load Resistor, item # DI34ZR, at at least two lights that you plan to install on your 2010 Nissan Rouge, if after installing the LED blinkers you have a hyperflash situation. If you still have hyper flash with two resistors installed you will need to install 2 more resistors at the other lights. You should install the LED blinkers first to determine if the resistors are required on your vehicle.

You will not need to calculate the Ohms, the resistor is built to build resistance to correct flash timing.

expert reply by: Robert G

0

Answer 1

If the lights on your trailer were acting fine prior to installing the LEDs then you need to start off by checking the ground connections for your lighting. Make sure they are securely connected to a clean, bare-metal surface as even some paint can…

view full answer...

Answer 2

It sounds like either you have the load resistor #DI34ZR connected to the wrong circuit, not connected quite right, or the vehicle uses a pulse width modulation type of wiring that could affect performance. I have included a picture that shows the…

view full answer...

Answer 3

The Diamond LED Light Bulb Load-Resistors #DI34ZR would be considered weather resistant. You wouldn't want to submerge them under water but they are designed to be mounted on trailer wiring or vehicle wiring in areas that can get wet from…

view full answer...

Answer 4

You will want to wire in a load resistor to any LED bulb that flashes quickly. Basically, the vehicle thinks a bulb is burnt out so you need to add a small load (resistor) to allow the bulb to stop flashing. The resistor gets wired into the…

view full answer...

Answer 5

Most trailer's are wired up so that the turn signals and the brake lights are carried on the same circuit. So what you are experiencing is normal, but there is a way to do what you are trying to accomplish. You will need to use a signal converter…

view full answer...

Answer 6

It sounds like you may just need to install some load resistors on the turn signal circuits of your truck. The hyper flashing you are experiencing occurs sometimes with LED lights because they only draw a fraction of the power that a standard…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Are Load Resistors Needed on a 2010 Nissan Rouge when Installing LED Blinkers

Product Page this Question was Asked From

Continue Researching