Availability of Trailer Hitch for 2003 Chevy Silverado with 10 inch Drop Bumper

Question

Question:

I installed a 10inch ranch hand back bumper on my 03 Chevrolet 1500hd and had to remove my factory receiver hitch because it couldnt be used with bumper. Do you guys offer a receiver hitch I can put back on my truck?

asked by: Eric S

1

Helpful Expert Reply:

The Curt trailer hitch part # 13339 is designed to fit your 2003 Chevy Silverado 1500HD with a 10 inch drop bumper so it would be a great option.

expert reply by: Jameson C

1

Answer 1

I have the perfect option for you in the Curt Trailer Hitch Receiver part #13339 which is a confirmed fit for a 2004 Chevrolet Silverado 1500 model and actually designed specially for models with an aftermarket bumper. As you can see, there are no…

view full answer...

Answer 2

There are a few different options to choose from depending on the style of 2003 GMC Sierra 1500 HD that you have. If you have a 10 inch Deep Drop Bumper I recommend the Curt #13339. If you have the aftermarket Roll Pan Bumper I recommend the Curt…

view full answer...

Answer 3

If you are looking for a trailer hitch for a 2002 GMC Sierra 2500HD then I recommend the Curt Trailer Hitch Receiver part #C13108 because it's a custom bolt on option. The Curt Trailer Hitch Receiver part #C13902 that you asked about may work but…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Availability of Trailer Hitch for 2003 Chevy Silverado with 10 inch Drop Bumper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching