Spare Tire Cover Recommendation for 27 inch Diameter Tire

Question

Question:

Looking for a spare tire full cover for my wheel/tire which measures 27foot diameter and 9inch wide in either black or dark grey. Spare will be insider the car, not mounted on the back of the vehicle.

asked by: Phil

0

Expert Reply:

For a black spare tire carrier designed to fit a 27 inch diameter wheel and tire we have the Camco cover part # CAM45258 which is a great option that would work well.

expert reply by: Jameson C

0

Answer 1

A 205/75R15 trailer tire, when inflated, measures 27.1 inches in diameter and 8.5 inches wide, so you'll need a cover that will fit those dimensions. So instead of a cover for a 26 inch spare tire, you'll need a cover for a 27 inch tire, and…

view full answer...

Answer 2

There are several pieces of information needed to pick out all the components needed to install brakes on a trailer axle. To see an article that covers everything check out the FAQ article I attached that covers everything you will need and will walk…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Answer 12

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Spare Tire Cover Recommendation for 27 inch Diameter Tire

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching