Correct Wiring Needed to Install Optronics Round LED Trailer Light

Question

Question:

I would like to replace the tail lights on my Serro Scotty with Sealed, 4inch Round LED Trailer Stop, Turn and Tail Light, Flange Mount, 3-Function, 10 SuperDiode. The product information states, Requires plug for complete installation, sold separately. I would like to purchase these too, but I am not clear which item this is. Do you have a description or item number I can use to look them up?

asked by: Wade S

0

Expert Reply:

To install the Optronics Round LED Light # STL42RB you can use the Optronics 3-Wire Pigtail # A45PB. This has the three 20 gauge wires for stop, turn, and tail light functions. The red wire is for stop and turn, the black for tail lights, and the white is the ground wire.

expert reply by: Charles S

0

Answer 1

The Sealed, 4" Round LED Trailer Stop, Turn and Tail Light, Flange Mount, 3-Function, 10 SuperDiode #STL42RB can be ran to the rear of a vehicle as additional stop/turn lights. Basically you'd just need the correct install harness like the…

view full answer...

Answer 2

We offer several lights and may have just what you are looking for that will fit your 2005 Airstream. Thank you for the photo of your lights. You will want to take a measurement to be sure you get a light that will match the housing you are…

view full answer...

Answer 3

You can absolutely replace the incandescent lights on your livestock trailer with LED assemblies. Other than replacing the lights themselves, there is nothing else that you will need to do. Your existing wiring (assuming it is in good condition) can…

view full answer...

Answer 4

If a light has just 1 wire that means that it grounds through its mounting hardware. Be sure to use steel hardware and mount the light to a clean and corrosion free bare metal surface. If there isn't a steel surface where you want to mount the…

view full answer...

Answer 5

The 4 inch Round Sealed LED Stop, Turn or Tail Light, item #STL42RB, uses a 3 wire pig tail, item #A47PB or #A45PB, to connect to your existing trailer wiring. The plug on the pigtail plugs into the back of the tail light and is then hard wired to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...