How To Install A 2-5/16 Inch Hitch Ball To A Draw Bar That Has Limited Access to the Hitch Ball Nut
Question:
I want to replace my 2 5/16, 1 1/4 shank ball. The nut is recessed within what is essentially a box on the draw bar. There is not enough clearance within this box to get a wrench on the nut. It appears to me that the torque must be applied via the balls wrench flats rather than to the nut. Is this method of tightening acceptable and Is it possible to apply 450 ft. lbs. of torque with this method?
asked by: Randy G
Expert Reply:
It sounds like you might have the 2-5/16 inch hitch ball on a weight distribution head assembly which can limit the access to the hitch ball nut. The weight distribution head is bolted to the the shank that inserts into the trailer hitch. I am including a link to a picture of what a weight distribution head might look like to help you decide if that is what you might have.
To tighten the nut on the hitch ball you will need to use a 1-7/8 inch socket instead of a wrench. The socket should be able to fit on the nut and allow you to torque the hitch ball. I am sending a video link of a weight distribution system being installed on a vehicle. At the 1:40 mark of the video it will show you how our installer attached the hitch ball to the weight distribution head.
Product Page this Question was Asked From
2-5/16" Hitch Ball - 1-1/4" Diameter x 2-3/4" Long Shank - Chrome - 12,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-3/4 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 12000 lbs GTW
- Class IV
- Class V
- Draw-Tite
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: 2-5/16" Hitch Ball - 1-1/4" Diameter x 2-3/4" Long Shank - Chrome - 20,000 lbs
- Q&A: Recommended Torque for Tightening Curt Hitch Balls to Ball Mount
- Shop: 2-5/16" Hitch Ball - 1-1/4" Diameter x 2-1/2" Long Shank - Raw - 30,000 lbs
- Shop: Curt Forged Ball Mount for 2-1/2" Hitches - 2-1/2" Rise - 4" Drop - 20,000 lbs
- Video: Curt Chrome 2-5/16 Inch Hitch Ball Review
- Shop: Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
- Shop: 2-5/16" Hitch Ball - 1-1/4" Diameter x 2-3/4" Long Shank - Chrome - 20,000 lbs
- Shop: 2-5/16" Hitch Ball - 1-1/4" Diameter x 2-3/4" Long Shank - Chrome - 12,000 lbs
- Shop: 2-5/16" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Stainless Steel - 6,000 lbs
- Search Results: reese ball mount
- Search Results: reese
- Shop: Trailer Hitch
- Article: How to Choose the Right Trailer Hitch Class
- Video: Choosing the Right Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: hitch
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Tow Ready 4-Pole Mounting Bracket Installation
- Shop: Brake Controller
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Video: Choosing the Right Brake Controller
- Search Results: hitch pin
- Search Results: brake controller
- Shop: Gooseneck Hitch
- Article: My Trailer Hitch Doesn't Fit
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
on Trailer Hitch Ball
Norm J.
8/9/2020
Im doing the right thing with the Reese 66559. Concerned with the ball. Needed and ordered the 2 5/16 ball. Problems is if it takes 400 ft lbs to torque where do I get a torqe wrench with out paying $200 and most more than that. I dont even see a torque one on your company to cover 400 lbs. Any help?