Will Dutton-Lainson Ball Adapter Plate Work With Power Winch 912

Question

Question:

Do you have a hitch ball adapter plate that will work with a Power Winch 912

asked by: Cliff W

0

Expert Reply:

Although they are not tested together, the Dutton-Lainson Ball Adapter Plate, part # DL24053 may work with your winch.

The two holes nearest the ball hole are 2-1/2 inches apart on center and the single hole is 3 inches back from the centerline of the other two holes. I have attached a photo of the adapter plate with the hole dimensions noted you can check out.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

The Dutton-Lainson TW4000 StrongArm Electric Winch #DL25200 is a great option for you. It can be mounted directly to your trailer or you can use the hitch ball adapter plate #DL24053 to use with your trailer hitch ball.

view full answer...

Answer 2

I may have another option for you, but the SW2060 is no longer available. The only plate we have that is similar in design is the Dutton-Lainson Ball Adapter Plate #DL24053 which is designed for StrongArm SA Series electric winches and has a…

view full answer...

Answer 3

On the Dutton-Lainson Ball Adapter Plate, #DL24053, it is designed for the Strongarm SA Series electric winches that have a 3 hole mount. I am sending you a link that shows the base hole pattern with the base hole diameters, so you might be able to…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Will Dutton-Lainson Ball Adapter Plate Work With Power Winch 912

Product Page this Question was Asked From

Continue Researching