Trailer Hitch & Related Items for 2009 Pontiac Vibe
Question:
will hitch C12221 fit my 2009 Pontiac Vibe?
asked by: Carlos L
Expert Reply:
Yes, the Curt 1-1/4-inch Class II hitch # C12221 will fit on your 2009 Pontiac Vibe so long as it is the GT version. If your Vibe is other than the GT version then instead you will want Curt's hitch # C12228. Both hitches share the same 250-lb tongue weight (TW) capacity and 2500-lb towing capacity. An installation video for each hitch is linked.
The recommended ball mount to use in either hitch is part # C45521. Use pin and clip kit # F-4 to secure the ball mount in the hitch. For a compatible hitch ball use either 2-inch ball # A-82 or 1-7/8-inch ball # A-80.
For a wiring harness you can use 4-pole kit # 118460. A helpful installation article is included.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 250 lbs TW
- 2500 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 250 lbs TW
- 2500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Determining Replacement Hub And Bearings For Dexter P-12 SLR Trailer Axle
- Q&A: Troubleshooting A Clunking Noise Between A Fifth Wheel Hitch And Base Rails While Towing
- Q&A: Replacement Parts for Lippert Coach Step on Class A Motorhome
- Q&A: Correct Replacement for Advent Analog Wall Thermostat ACTH1
- Q&A: Trailer Hitch Fit for 2019 Mercedes-Benz Sprinter 2500 with 170 Inch Wheelbase and Standard Bumper
- Article: 2023 Best Gifts for Haulers & Towers
- Q&A: Replacement Parts for Fan-Tastic Vent 8000 Series
- Q&A: Scissor Jack Recommendation to Replaced Damaged Ones on R Pod Trailer
- Article: Best Ladder Racks
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Article: Rooftop Cargo Carriers
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Flat Towing Package for 2018 Jeep Wrangler JL and JL Unlimited