Which Fuse Number Carries Trailer Running Light Circuit on 2014 Chevy Silverado

Question

Question:

What number is the fuse in the fuse panel

asked by: Steve

0

Expert Reply:

From the research I did on your vehicle it looks like the position 15 of the mini fuse section has the trailer running light circuit.

expert reply by: Jameson C

0

Answer 1

If you are looking for the fuses on your 2015 Chevrolet Silverado 1500 that are tied to your trailer wiring then those will be in the fuse box in the engine compartment. You can find this information as well as a list of what all the fuses are tied…

view full answer...

Answer 2

On your 2006 Ford Expedition, there should already be a factory installed trailer connector. It will either be a 4-Way flat or a 7-Way blade. If your vehicle has a 4-Way flat, you will need to add Adapter 4 Pole to 7 Pole and 4 Pole, #37185. On this…

view full answer...

Answer 3

The number 15 fuse in the engine bay fuse box is responsible for the trailer parking lamps. For future reference, the owner's manual will tell you where all the fuses are located and what they do.

view full answer...

Answer 4

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 5

Since your trailer is brand new I suggest a visit to the selling dealer or to another authorized service/repair center. Small parts such as light lenses are easy to replace and inexpensive, but troubleshooting the blown fuse problem is not. Finding…

view full answer...

Answer 6

Thank you for the positive feedback David. The Furrion Vision S Wireless RV Backup Cameras like part #FOS05TASF are activated by the running light circuit so you would need to have your running lights on to activate the camera. However, I have heard…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Which Fuse Number Carries Trailer Running Light Circuit on 2014 Chevy Silverado

Product Page this Question was Asked From

Continue Researching