Sway Bar Recommendation for 2013 Coachmen Mirada V10 Ford F53 Chassis

Question

Question:

What kit should I order for 32foot Caoachman Mirada V10 ford 7000 fronts 12000 rears 19.5 tires . Not used to sway drive tractor trailer for living need to stiffen it up Thanks 18,000 gvw

asked by: Kurt J

0

Expert Reply:

Your 2013 Coachmen Mirada is built on a Ford F-53 chassis so the Roadmaster sway bar part # RM-1139-148 that you referenced would be perfect. This is for V10 models with GVWR of less than 24k so it would work well.

For a front sway bar then you would want the part # RM-1139-148. The rear bar will make the biggest difference but the front will also help quite a bit.

expert reply by: Jameson C

0

Answer 1

For your 2014 Fleetwood Bounder Class A motorhome that is based on the Ford F-53 with V10 engine you can use the Roadmaster rear Anti-Sway bar #1139-144. For a front anti-sway bar you can use #RM-1139-148.

view full answer...

Answer 2

Your 2007 Four Winds Hurricane is build on a Ford F-53 chassis which is notorious for roll and sway issues. The best thing you can do to help with this is a rear sway bar. The rear sway bars on the F-53 chassis make the biggest difference. For that…

view full answer...

Answer 3

Your 2015 Newmar Canyon Star Model 3610 is built on a Ford F-53 chassis which is plagued with handling issues. The biggest improvement you can make is a rear sway bar. For that you would want the part #1139-144. Next you would want to go with a front…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 8

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...