Can Welded On Broken Trailer Coupler be Replaced

Question

Question:

I have a small trailer for my 12ft fishing boat, tge coupler im sure is a no name cheap coupler but it has been plug welded to the trailer so i cant repkace it. I need a rebuild kit for the coupler. Will this work? Thank you.

asked by: Steve H

0

Expert Reply:

We don't have generic coupler repair kits that I can recommend, but most likely your coupler can be replaced if you take it to a qualified welder in your area. They should have no problem removing the coupler and installing a new one.

If your hitch ball is 2 inches the part # F343000301 would work for you. This mounts to a 3 inch channel.

If you have a 1-7/8 inch ball you would want the part # T4845000.

expert reply by: Jameson C

0

Answer 1

I went and pulled a Trailer Coupler 2" Ball 3" Channel Tongue #DL13800 from our warehouse to get the dimension you requested and the distance from the underside of the coupler to the center of the holes on the side of the coupler measures…

view full answer...

Answer 2

I pulled one of the part #DL13800 couplers from the warehouse and took a few measurements. I have attached a photo of the coupler with the dimensions noted you can check out. The critical measurements you mentioned such as the holes from the bottom…

view full answer...

Answer 3

For a trailer hitch receiver for your travel trailer, I recommend the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide #13703. This hitch can be welded for a no-drill application as you stated, or it can be bolted in…

view full answer...

Answer 4

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 5

The one you were looking at item #C25194 is not but we have some repair kits that are. The repair kits are brand specific so if you don't have one of the below couplers feel free to email me back with kind you have and I will be happy to find the…

view full answer...

Answer 6

The Coupler Repair Kit part #C25194 is designed for Curt trailer couplers that use a 2" hitch ball. Since you have a Fulton trailer coupler I cannot recommend you use this kit. Instead, I recommend taking a look at part #F670801 which is for…

view full answer...

Answer 7

We do offer repair kits for Fulton and other brands of trailer couplers. These repair kits are confirmed based on the original coupler series number, which is usually stamped into the housing or printed on a sticker. For example, the Repair Kit for…

view full answer...

Answer 8

I recommend the Kenda 205/65-10 Bias Trailer Tire with 10" White Wheel #AM3H390 for your 1994 Coleman Pioneer Arcadia. The 205/65-10 is the current size tire that replaced the 20.5x8-10 you have on your Coleman. The wheel uses the 5 on…

view full answer...

Answer 9

The Coupler Repair Kit for 2" Curt Couplers #C25194 has not been tested with the Reese Tow Power 74280 coupler but it should work well. Mechanically these style couplers are not very different, so the parts should work without issue. This is our…

view full answer...

Answer 10

Based on what we could find, the AL-KO 8490 is a 3,500 lb axle, and your info stating the 5 on 4-1/2" bolt pattern and 10" x 2-1/4" drum size supports that as well. I do recommend verifying what you need by taking apart your current…

view full answer...

Answer 11

The Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR is a single zone 3 wire thermostat like the one you are describing. I have attached the wiring diagram for this thermostat and the control box below for your reference.

view full answer...

Can Welded On Broken Trailer Coupler be Replaced

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching