Can GloLIGHT LED Light part # STL111RCB Fit in Opening of Custer Light Mounting Box AL65-0

Question

Question:

Optronics STL111RCB LED Lamp has bracket BK70BB associated with it that has listed the opening at 6-11/16inch x 2-5/8. Custer AL65-0 Oval Lamp Housing has listed the opening at 6-1/2inch x 2-1/2. Are these compatible? I could not find any housings that did not listed the same opening as the bracket,

asked by: David

0

Expert Reply:

Yes, if you wanted to install the # STL111RCB in the opening of the # AL65-0 all you would need is the correct grommets, part # a70gb.

expert reply by: Jameson C

0

Answer 1

To add a lighted license plate mount to the LED Light Kit #98174LED on your cargo carrier I recommend the Optronics #LP55CB. The bracket simply gets attached to the carrier with a couple of screws (not included) and the wiring harness can be tied…

view full answer...

Answer 2

Although the Snap-on Reflector Ring, #A78RXB, will not fit the STL178 series lights like the Optronics GLOLight LED Stop/Turn/Tail Light #STL178RFPB, I do have a solution for you. Take a look at the Sealed, 6-1/2" Oval LED Trailer Stop, Turn and…

view full answer...

Answer 3

Since there isn't a specific light kit that will fit the Curt carrier #C18153, what you will need to do is use a light kit like #98174LED, and then add 2 brackets part #BK70BB as they work with 6-1/2 inch oval lights. You will also need some…

view full answer...

Answer 4

You'd have to drill a pretty large hole to fit the plug ends of the #98174LED through the brackets. I'd rather recommend you zip tie the harness to a much smaller hole instead of drilling the roughly 1-1/4 inch hole you'd have to drill,…

view full answer...

Answer 5

You could use the LED kit part #98174LED to add the lights and wiring to your bike rack and then use the bracket #BK70BB and you'd be set. You'd have to attach the brackets to the bike rack and then once installed the lighting harness would…

view full answer...

Answer 6

The GloLight LED Trailer Tail Light #STL111RB will stick out about an inch when installed. It's pretty minimal and also the standard size for this style of light.

view full answer...

Answer 7

Yes, it is possible to buy just the wiring harness for the LED Light Kit for Draw-Tite, Tow Ready, Pro Series, and Rola Railed Cargo Carriers item #98174LED. It is the Optronics Replacement Cargo Carrier Light Harness item #WHCETR1B.

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Can GloLIGHT LED Light part # STL111RCB Fit in Opening of Custer Light Mounting Box AL65-0

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching