Replacement Wiring Harness for Cargo Rack LED Light Kit

Question

Question:

Hi there, Is it possible to buy the wiring harness from this kit? I want to surface mount lights and was hoping to use that to connect everything. Thanks

asked by: David D

0

Expert Reply:

Yes, it is possible to buy just the wiring harness for the LED Light Kit for Draw-Tite, Tow Ready, Pro Series, and Rola Railed Cargo Carriers item # 98174LED. It is the Optronics Replacement Cargo Carrier Light Harness item # WHCETR1B.

expert reply by: Jerred H

0

Answer 1

The GloLight LED Trailer Tail Light #STL111RB will stick out about an inch when installed. It's pretty minimal and also the standard size for this style of light.

view full answer...

Answer 2

You could use the LED kit part #98174LED to add the lights and wiring to your bike rack and then use the bracket #BK70BB and you'd be set. You'd have to attach the brackets to the bike rack and then once installed the lighting harness would…

view full answer...

Answer 3

Yes, if you wanted to install the #STL111RCB in the opening of the #AL65-0 all you would need is the correct grommets, part #a70gb.

view full answer...

Answer 4

Although the Snap-on Reflector Ring, #A78RXB, will not fit the STL178 series lights like the Optronics GLOLight LED Stop/Turn/Tail Light #STL178RFPB, I do have a solution for you. Take a look at the Sealed, 6-1/2" Oval LED Trailer Stop, Turn and…

view full answer...

Answer 5

To add a lighted license plate mount to the LED Light Kit #98174LED on your cargo carrier I recommend the Optronics #LP55CB. The bracket simply gets attached to the carrier with a couple of screws (not included) and the wiring harness can be tied…

view full answer...

Answer 6

You'd have to drill a pretty large hole to fit the plug ends of the #98174LED through the brackets. I'd rather recommend you zip tie the harness to a much smaller hole instead of drilling the roughly 1-1/4 inch hole you'd have to drill,…

view full answer...

Answer 7

Since there isn't a specific light kit that will fit the Curt carrier #C18153, what you will need to do is use a light kit like #98174LED, and then add 2 brackets part #BK70BB as they work with 6-1/2 inch oval lights. You will also need some…

view full answer...

Answer 8

You could use the LED kit part #98174LED for a light kit and then use the bracket #BK70BB to mount the lights to your bike rack and the taillights would all be visible.

view full answer...

Answer 9

I would be happy to help you set up your rear light kit item #98174LED. I just called my rep at Saris to get the total length of your MTR Bike Rack for 4 Bikes. He said that bike rack is 56" long from the hitch to the back of the last extension.…

view full answer...

Answer 10

We can get you the light kit and license plate holder for a hitch mounted cargo carrier, though we don't have a cargo carrier that is 48 inches wide, with the widest one we offer being half that width. We also don't do any type of custom…

view full answer...

Answer 11

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Replacement Wiring Harness for Cargo Rack LED Light Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching