Bearing Buddy Recommendation for Hub Bore of 1.97 inches

Question

Question:

I used an electronic caliper and find I need a 1.97 outside dimension for my hub. Any suggestions? I have tried a 1.98 and can not make it fit. Thanks, Bill

asked by: Bill

1

Helpful Expert Reply:

For a hub bore of 1.97 inches going with a Bearing Buddy part # BB1968SS would be the closest match. The .02 inch difference would only mean the Bearing Buddy would fit slightly easier.

expert reply by: Jameson C

1

Answer 1

The Unitized Oil Seal #10-63 is the correct replacement oil seal for the phle ap3137n2 oil seal that you have. If you want to switch to a grease hub you will need the Grease Seal #GS-2250DL.

view full answer...

Answer 2

I looked up your Shurflo 200-210-39 and based on it's specs the HydroMax RV Fresh Water Pump #P25201 would work great as a replacement. It's similar in flow and PSI as well.

view full answer...

Answer 3

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 4

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 11

Replacement arms are available for the Roadmaster EZ5 Base Plate Kit #RM-521569-5 for your 2015 Honda Fit with the part #RM-ARMS. When the original base plate brackets and arms were manufactured, they were made as one part. To be sure that the new…

view full answer...

Answer 12

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Bearing Buddy Recommendation for Hub Bore of 1.97 inches

Product Page this Question was Asked From

Continue Researching