Recommended Easy to Install Trailer Hitch and Wiring Harness for 2001 Jeep Cherokee
Question:
I have a 2001 jeep cherokee. I want a 5000 lb hitch that is direct fit with abaolutley no drilling or welding needed to install it. i want to unpackage it, bolt it on and go pull firewood on my trailer. i also need a harness that will plug in to the harness with no modifications needed. can you please provide me with some part numbers?
asked by: LARRY M
Expert Reply:
The Curt Class III Round Tube Receiver Hitch # 13160 is compatible with your 2001 Jeep Cherokee and requires no drilling or welding for installation. It is rated for 5000 lbs., however you will still be limited to the towing capacity of your Cherokee which, from my research, is only 2000 lbs. You will want to verify with your owners manual just how much weight you Jeep can tow.
The Tekonsha Wiring Harness # 118354 is custom-fit for you Cherokee, and plugs in behind an interior trim panel in the rear cargo area on the driver's-side. You will need to remove the spare tire and a side panel to find the harness to plug into but once that's complete it's ready to go.
I've attached installation videos of the hitch and wiring on a 2001 Cherokee for you.
Also, the Ball Mount Kit # 989900 includes 2 ball mounts with different rise and drop measurements, both a 2 inch and a 1-7/8 inch hitch ball, and a pin and clip.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How to Replace Interior Ram Jack Rod and Nut # TJD-12000-RODNUT on 12000 Series Jacks
- Q&A: What is the Difficulty Level for Installing the Curt Trailer Hitch on a 1998 Jeep Cherokee
- Q&A: Replacement Bearings and Seals for a ShoreLandr Trailer with Dico 45263 Hubs
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Is Curt Class III Trailer Hitch # 13084 a Correct Fit for the 1997 Jeep Cherokee Sport
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Disc Brake Kit Availability for a Dexter 10k Axle
- Q&A: Replacement Parts for Dexter Motorhome Axle 8-133
- Article: How to Choose a High-Low Adapter
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose the Right Trailer Hitch Class
- Article: How Level Should a Tow Bar Be When Flat Towing
- Article: Wiring a Tow Vehicle to Tow a Dinghy
- Article: How to Measure for Trailer Hitch Drop