Does Curt Hitch C11347 Fit a 2012 Fiat 500 Abarth

Question

Question:

For 2012 fiat 500 abarth....your cite seems to imply the curt model will work while other reviews say it does NOT work on 2012 models. I am considering buying a 2012 but want to make sure it can take the hitch. Help clarify this please.

asked by: Nancy K

1

Helpful Expert Reply:

Curt manufacturing has informed us that their hitch part # C11347 is a confirmed fit for your 2012 Fiat 500 and was specifically made for the Abarth models so it will fit and work well.

I attached an install video for this hitch for you to check out as well.

expert reply by: Jameson C

1

Answer 1

The Curt Trailer Hitch Receiver part #C11347 is a confirmed fit for a 2012 Fiat 500 Abarth with the factory muffler. I have attached a photo of said muffler installed on the vehicle that the trailer hitch is designed to work with. If you have an…

view full answer...

Answer 2

Based on the bearing numbers that you have the correct grease seal would be the part #10-9.

view full answer...

Answer 3

The most common cause for wheel bearing grease to leak onto drum brake components is accidental over-filling. Once grease gets onto the brake pads it is neither easy nor a terribly good idea to clean the grease off them. They really should be…

view full answer...

Answer 4

It is possible that you have single lip seals and need to replace them with double lip seals to avoid the grease leaking from the back of the hub. A double lip seal will have a stronger seal for EZ lube spindles such as #TRU74FR. The force of the…

view full answer...

Answer 5

When installing the castle nut on the end of the spindle, there is no specific torque rating. The nut is ran down until there is no side to side play in the hub, and then backed off to the next notch in the castle nut so the retainer can secure the…

view full answer...

Answer 6

What's happening is that you are actually overfilling your hubs which grease and that is why the seal is leaking. This is very easy to do with EZ lube spindles and Bearing Buddies which is why we generally recommend just packing the hubs by hand…

view full answer...

Answer 7

The Dexter Spindle Nut #6-183 used with your 50mm Nev-R-Lube bearing #31-71-3, requires 145 to 155 ft/lbs of torque, according to the manufacturer's specifications. See attached diagrams for step by step instructions.

view full answer...

Answer 8

Yes, the etrailer Hitch Mounted Spare Tire Carrier item #e98ZR will fit a 4 x 100 wheel. The universal bolt pattern accommodates a variety of tire and wheel sizes. I have linked a review video and a diagram I made to show you the dimensions of the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Does Curt Hitch C11347 Fit a 2012 Fiat 500 Abarth

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching